A050130380S7055xMWeb Smart Managed5-Port 10/100 Fast EthernetSwitch w/VLAN SupportInstallation GuideCopyright January 2005VERSITRON, Inc.83 Albe Drive
www.versitron.com102.4 VLAN FunctionThe switches support two VLAN modes. One is Port-based VLAN and the other is 802.1Q VLAN.The following configurati
www.versitron.com11Summary of VLAN Group Lookup (Group Mapping Index)Input Packet Type Port-based VLAN Mode 802.1Q VLAN ModeUntagged packet PVID bit3-
www.versitron.com122.7 Making UTP ConnectionsTP Port ConfigurationUse management function to set the required TP port configuration. It is recommended
www.versitron.com132.9 LED IndicatorsFunctionsPOWER: indicates the status or the power supplied to the switch100/10: indicates the connection speed be
www.versitron.com143. Web Management3.1 Web BrowserThe system features an http server that can serve the management requests coming from any webbrowse
www.versitron.com15The web page is shown as follows when a successful login is performed:The left side shows the menu list. The list includes:[Port Se
www.versitron.com16Port SetupThis page is used to set the port configuration for each port. As auto-negotiation function isenabled, speed and duplex s
www.versitron.com173.4 VLAN SetupVLAN Mode SelectPort-based VLAN: Port-based VLAN802.1Q base VLAN: IEEE 802.1Q Tag-based VLANClick [Apply] to make cha
www.versitron.com183.4.1 Port-based VLANClick [VLAN Mapping Table]This page is used to setup members for each VLAN group. Total of 16 VLAN groups ares
www.versitron.com19Click [Port PVID Setting]This page is used to setup PVID and Tag mode for each port as follows:PVID: The setting value is used for
www.versitron.com2The information contained in this document is subject to change without prior notice.Copyright © All Rights Reserved.TRADEMARKSEther
www.versitron.com203.4.2 802.1Q VLANClick [VLAN Mapping Table]This page is used to setup member ports for each VLAN group. Total of 16 VLAN groups are
www.versitron.com21Click [Port PVID Setting]This page is used to setup PVID and Tag mode for each port as follows:PVID: The valid value range is 1 ~ 4
www.versitron.com223.5 Password SetupPassword is used for checking authority for accessing the switch. To change password setting,enter your new passw
www.versitron.com233.6 Restore DefaultThis command is used to restore all settings back to factory default values. Click [Restore] toapply immediately
www.versitron.com243.7 Reboot DeviceThe command is used to reboot the switch remotely over the network. Normally, it is used afterIP settings are chan
www.versitron.com253.8 AboutAbout page shows switch model name and software versions.
www.versitron.com26Appendix: Factory Default ValuesSettings Factory Default ValuesDHCP mode EnabledStatic IP address 192.168.0.2Netmask 255.255.255.0
www.versitron.com3Table of Contents1. Introduction... 41.1 Features...
www.versitron.com41. IntroductionThis guide describes the specifications and installation instructions for the following twomanaged 10/100 switch seri
www.versitron.com51.1 Features• The 10/100BaseTX switched ports support:- Auto-speed sensing for 100Mbps or 10Mbps connection- Auto configuration f
www.versitron.com61.2 SpecificationsS7055xM P1-P4 Port 1 ~ Port 4 Twisted-pair switched ports (TP ports)S7075xM P1-P6 Port 1 ~ Port 6 Twisted-pair swi
www.versitron.com71.3 FX Port Optical SpecificationsModel Connector Wavelength Max. Distance Rx sensitivityS70553M MM*1 ST 1310nm -20 ~ -14dBm -31dBmS
www.versitron.com82. Installing the Switches2.1 UnpackingCheck to see that you have everything before you start the installation.. Installation guide.
www.versitron.com92. Connect the power adapter cable to the switch before connecting the adapter to the AC outlet.2.3 Port ConfigurationThe switches p
Comments to this Manuals